QUESTION 5
MultiCorp is running Smartcenter R71 on an IPSO platform and wants to upgrade to a new Appliance with R77. Which migration tool is recommended?
A. Download Migration Tool R77 for IPSO and Splat/Linux from Check Point website.
B. Use already installed Migration Tool.
C. Use Migration Tool from CD/ISO
D. Fetch Migration Tool R71 for IPSO and Migration Tool R77 for Splat/Linux from CheckPoint website
Correct Answer: A
QUESTION 6
MegaCorp is running Smartcenter R70, some Gateways at R65 and some other Gateways with R60.
Management wants to upgrade to the most comprehensive IPv6 support. What should the administrator do first?
A. Upgrade Smartcenter to R77 first.
B. Upgrade R60-Gateways to R65.
C. Upgrade every unit directly to R77.
D. Check the ReleaseNotes to verify that every step is supported.
Correct Answer: D
QUESTION 7
MicroCorp experienced a security appliance failure. (LEDs of all NICs are off.) The age of the unit required that the RMA-unit be a different model. Will a revert to an existing snapshot bring the new unit up and running?
A. There is no dynamic update at reboot.
B. No. The revert will most probably not match to hard disk.
C. Yes. Everything is dynamically updated at reboot.
D. No. At installation the necessary hardware support is selected. The snapshot saves this state.
Correct Answer: D
Latest Checkpoint 156-315.77 Exam Study Question
QUESTION 8
Which is the lowest Gateway version manageable by SmartCenter R77?
A. R65
B. S71
C. R55
D. R60A
Correct Answer: A
QUESTION 9
Can you implement a complete IPv6 deployment without IPv4 addresses?
A. No. SmartCenter cannot be accessed from everywhere on the Internet.
B. Yes. Only one TCP stack (IPv6 or IPv4) can be used at the same time.
C. Yes, There is no requirement for managing IPv4 addresses.
D. No. IPv4 addresses are required for management.
Correct Answer: C
QUESTION 10
A ClusterXL configuration is limited to ___ members.
A. There is no limit.
B. 16
C. 6
D. 2
Correct Answer: C
Checkpoint 156-315.77 Exam Dumps Question & Answer
QUESTION 11
Select the command set best used to verify proper failover function of a new ClusterXL configuration.
A. reboot
B. cphaprob -d failDevice -s problem -t 0 register / cphaprob -d failDevice unregister
C. clusterXL_admin down / clusterXL_admin up
D. cpstop/cpstart
Correct Answer: C
QUESTION 12
You are troubleshooting a HTTP connection problem. You've started fw monitor -o http.pcap. When you open http.pcap with Wireshark there is only one line. What is the most likely reason?
A. fw monitor was restricted to the wrong interface.
B. Like SmartView Tracker only the first packet of a connection will be captured by fw monitor.
C. By default only SYN pakets are captured.
D. Acceleration was turned on and therefore fw monitor sees only SYN.
Correct Answer: D
QUESTION 13
Which two processes are responsible on handling Identity Awareness?
A. pdp and lad
B. pdp and pdp-11
C. pep and lad
D. pdp and pep
Correct Answer: D
Checkpoint 156-315.77 Preparation Exam dumps
QUESTION 14
Which three of the following are ClusterXL member requirements?
1) same operating systems
2) same Check Point version
3) same appliance model
4) same policy
A. 1, 3, and 4
B. 1, 2, and 4
C. 2, 3, and 4
D. 1, 2, and 3
Correct Answer: B
QUESTION 15
You run cphaprob -a if. When you review the output, you find the word DOWN. What does DOWN mean?
A. The cluster link is down.
B. The physical interface is administratively set to DOWN.
C. The physical interface is down.
D. CCP pakets couldn't be sent to or didn't arrive from neighbor member.
Correct Answer: D
